Unscramble Codes E1,E2,E3,E4,E5,E6,E7,E8,E9,E10,E11,E12,E13,E14,E15 For Thermador CT127, CT130, CT230 Models

The most common codes we see at www.fixyourboard.com are E3,E4, E10,  but here is the full list for CT127, CT130, CT230, CMT22 models:

Does your Thermador Controller look like this?  Below is the full list of codes and the meaning according to Thermador:

ERC_CT127_CT130_CT230

ERC For CT127_CT130_CT230

Error Code:     E1
Cause:     Control Board
Example:     Disables clean in both ovens; allow cooking
Corrective Action:     Replace control board

Error Code:     E2
Cause:     Sensor or Control Board
Example:     Oven temp over 625F or clean temp over 890F
Corrective Action:     Check sensor

Error Code:     E3
Cause:     Open Sensor
Example:     Disables cooking in affected oven
Corrective Action:     Check sensor

Error Code:     E4
Cause:     Shorted sensor
Example:     Disables cooking in affected oven
Corrective Action:     Check sensor

Error Code:     E5
Cause:     Control Board
Example:     Disables clean in both ovens; cooking useable
Corrective Action:     Replace control board

Error Code:     E6
Cause:     Selector Switch
Example:     Disables individual cook modes in affected oven
Corrective Action:     Check all functions; replace selector switch if one-piece Dreefs; replace control board

Error Code:     E7
Cause:     Control Board
Example:     Remains in display; oven unusable
Corrective Action:     Replace control board

Error Code:     E8
Cause:     Control Board
Example:     Remains in display; oven unusable
Corrective Action:     Replace control board

Error Code:     E9
Cause:     Latch
Example:     Latch motor may run but switches do not cycle
Corrective Action:     Replace latch in affected oven

Error Code:     E10
Cause:     Control Board
Example:     Checksum error
Corrective Action:     Replace Dreefs board

Error Code:     E11
Cause:     Latch Problem
Example:     Will not clean
Corrective Action:     Replace latch in affected oven

Error Code:     E12
Cause:     Latch Problem
Example:     Will not clean
Corrective Action:     Replace latch in affected oven

Error Code:     E13
Cause:     Latch Problem
Example:     Latch does not run
Corrective Action:     Check for voltage to latch motor

Error Code:     E14
Cause:     Latch Problem
Example:     Loose latch switch
Corrective Action:     Check latch for proper operation

Error Code:     E15
Cause:     Control Board
Example:     Remains in display; oven unusable
Corrective Action:     Replace Dreefs board

The common parts and models that we see at www.fixyourboard.com are:

Parts: 368743, 369171, 431481, 35-00-536, 35-00-459

Models: CT127N01, CT127NPRS, CT130-03,  CT130S-03, CT227N01 CT23003, CT227NPRS, CT130S-03, CMT22NPRS

Thermador Oven Control Board 486752 / 14-33-347 – Door Lock Sequence and Errors

Are you having door lock problems with your Thermador control board 486752 or 14-33-347,  487604 or 316080103.   At www.FixYourBoard.com, we get questions about the door lock operation for this controller.  This post addresses this by describing the sequence of events when the controller is programmed for a clean cycle.    We hope this information will help you  troubleshoot door lock issues with the following model numbers: RDDS30, RDDS30QW, RDDS30V, RDDS30VQB, RDDS30VQB, RDDS30VRS, RDDS30VRS, RDFS30, RDF30, RDF30QB, RDF30QW, RDF30RS, RDF30RS, RDSS30, RED30V, RED30VQB, RED30VQRS, RED30VQW, REF30, REF30QB, REF30QW, REF30RS, RES30, RES30QB, RES30RS, RES30W, RDDS30, RDDS30QW, RDDS30, RDDS30V, RDDS30VQB, RDDS30VRS, RDFS30, RDF30, RDF30QB, RDF30QW, RDF30RS, RDSS30, RED30V, RED30VQB, RED30VQRS, RED30VQW, REF30, REF30QB, REF30QW, REF30RS,  RES30,  RES30QB,  RES30RS,  RES30W.

State 1 -Clean Button Pressed and Time Set  (Door still unlocked)

Note that the blue display show that clean mode has been selected and the total time for the clean mode.  The state of the switches is shown in the diagram.  Pins 7 and 8 are shorted together with switch #1.  This is the un-locked state.

Thermador_486752_clean_start1

State 1 -Display As Soon as Clean Time is Programmed

State 2 – Automatic Door Locks are Running (One Second after State 1)

After a second in state 1, the following happens:

  1. The clean light comes on.
  2. Controller turns on the door lock motor.
  3. This state only last until motor releases switch 1 and pins 7 and 8 are no longer connected.

 

Thermador_486752_clean_start2

 

State 3 – Lock Motor Still Spinning and Switch #1 is Not Pressed anymore.

Pins 7, 8 and 9 are not connected and the motor is still spinning.

Note that the display shows the “locked” even though switch #2 is not pressed yet and door is not locked.  

 

Thermador_486752_clean_door_all_pins_open

 

State 4 – Lock Motor has Stopped Spinning Because Switch #2 shorted pin 7 to 9.  Oven has turned on the heating elements.

Note that the display now says “ON”.  This means that switch #2 was pressed by the lock motor which shorted pin 7 to 9.  The oven will now reach cleaning temperature.

 

Thermador_486752_clean_on

 

State 5 – Fault State.  If the controller does not sense the door lock on pins 7 and 9.

In this fault mode, the controller will beep and show door on the screen.

Thermador_486752_clean_door_error

Error State – Control did not receive the locked signal on pins 7 and 9.